Remodelaholic | Utensil Drawer Organizer
Drawers are good in the kitchen area, primarily when they are all arranged! A customized adjustable utensil drawer organizer can continue to keep anything in its area and stay clear of messy drawers. Functions good for any drawer!
Hunting for other ways to manage your house? Organize a self-importance or lavatory drawer with these customized jewellery dishes. Organize the relaxation of your cupboards with these house preserving suggestions. And then consider a look at all of our organizing concepts as well.

Don’t we all have a dirty very little magic formula that appears like this in our kitchen area? A drawer that is just a mess.
Or probably this… what as soon as was arranged is no for a longer time.
I spent a several hrs with my saw, and now I no for a longer time have individuals individual skeletons in my closet! Now they look like this, thanks to a few Do it yourself drawer organizers.
And the greatest component is, they are both of those adjustable and one hundred% removable, so it is excellent for assembly your demands now and in a several many years, and renter-welcoming.
Look at the online video to see how, and examine the thorough directions down below.
Supplies Listing
To lower fees I used plywood. You could do this utensil drawer organizer project with 1×3 pine boards if you don’t have a table saw, but it will be much more expensive.
For my 1st endeavor I used one/4″ plywood, but after a several times the plywood started to bend.
Definitely the dividers would nonetheless operate, but I was not delighted with the finish outcome. So I made a decision to redo the dividers with one/2″ plywood. Balsa wooden or the skinny “craft” boards they provide at the components shop may possibly operate much better than the thinner plywood, but the enhanced value will be important, and the thicker plywood has experienced no difficulties.
For this project you will will need the following materials and tools:
Lumber
- 1 2′ x 4′ piece of one/2″ plywood
Equipment
Planning Customized Drawer Organizers
Be certain to plan right before executing these utensil drawer organizers to be certain they turn out just how you would like them.
Phase one: Measure your drawers.
Just take notice of both of those width and depth as effectively as drawer peak.
Phase 2: Determine how you would like your drawer divided.
Our recommended layouts that we used are down below. Some suggestions for designing your have drawer dividers:
Use your utensils to decide lengths and widths of sections so the dividers in good shape your demands. As you can view in the online video, washi tape is a excellent way to visualize the house with the dividers.
Consider about strain factors:
- Do you want a total size or width segment? Slash the dividers to the identical size or width of your drawer so they in good shape snugly. Then all you will need is spacers to separate just about every segment that set strain on the ends to keep them up.
- Do you want to divide the house lengthwise and widthwise? To reduce the sum of person spacers for the lesser sections I lower channels in the parts lower to the width of the drawer. Then for the larger sized sections I used spacers at the ends, and in the center to crack up the sections.
Recommended compact utensil drawer layout:
Entrance dividers for knives, forks, spoons etcetera. The other places I used for chopsticks, corn cob holders, and measuring spoons
Recommended massive utensil drawer layout:
I desired a larger sized spot for my apple slicer, the center compartments are evenly divided, and the closing compartment was made a decision after the many others had been in the drawer. I measured the remaining house so the compartments in good shape snugly in the drawer.
Phase 3: Rip the plywood.
Making use of your table saw rip the 2’x4′ sheet of plywood into 3″ strips along the 2′ facet. No table saw? You can have the lumber shop lower the plywood into the 3” parts and then use a miter saw for the other cuts.
Soon after you rip the plywood into 3” parts convey them into your house to acclimate. This will reduce the sum of bowing and shrinking when you assemble the lower parts in your drawers.
Soon after producing your shorter cuts, sand the corners to reduce splinters. You can also spray with a few of coats of polyurethane to make the parts washable.
Developing Tutorial for Little Utensil Divider
Phase one: Slash dividers.
Slash 3 @ 19″
Slash five @ 10″
Slash 3 @ 3 3/4″
Phase 2: Create channels for dividers to slide into.
Set depth of saw blade to eliminate one/8″ of material. Change the fence to 2 3/4″ and run both of those ends of (2) 19″ parts by way of saw. Then regulate the fence to 2 seven/8″. Repeat jogging both of those ends of the identical (2) 19″ parts. Continue to regulate saw by one/8″ increments (the width of your saw blade) right up until channel steps one/2″ or 3 one/4″ from the outside the house.
Repeat this process for the subsequent pair of channels. Setting the fence 1st at 6″ and modifying by one/8″ increments right up until you attain the outside the house measurement of 6 one/2″
For the center segment established your fence at 9 one/4″ and ending at 9 3/4″
Phase 3: Sand the edges to avoid splinters.
The smoother the surfaces are, the much better they will slide with each other and continue to be set.
Phase four: Assemble the 1st two sections.
Area a single of the channeled parts in opposition to the entrance of your drawer.
Area the (five) 10″ parts in the channels.
Situation the 2nd channeled piece in area, and regulate the 10″ dividers into just about every channel.
Phase five: Area the subsequent 2 parts.
Making use of the (3) 3 3/4″ parts and the past 19″ piece, area the 19″ piece and then the 3 3/4″ parts.
Phase 6: Measure and lower the closing parts.
Measure the remaining house, and lower 3 parts at that measurement. My closing measurement was four seven/8″
Phase seven: Place the three remaining dividers.
These will be held in area by tension to continue to keep all the other dividers in area, but they’re simply adjustable (as you can see in the online video).
Phase 8: Refill the drawer with your utensils!
Right here is the splendor of the parts remaining removable. They are adjustable! To have the divider parts in the center my chopsticks wouldn’t in good shape. So I adjusted the center parts to accommodate the size of the chopsticks.
Developing Tutorial for Larger Utensil Divider
Phase one: Slash dividers.
Slash five @ 19″
Slash 2 @ 6″
Slash 8 @ 3 seven/8″
Phase 2: Fit the parts with each other.
The strain of the spacing parts is what holds this all with each other. So I lower the closing parts after anything else is in the drawer. That way you get a pleasant tight in good shape.
Area all the parts you have lower so significantly in the drawer.
Commencing with the two 6″ parts, then a 19″ divider, then two 3 seven/8″ parts and yet another 19″ divider.
Continue in the pattern right up until you have all the parts in area.
Then evaluate the remaining house. My closing measurement was four thirteen/16″
Phase 3: Slash the closing parts.
Slash the closing 2 parts to your measurement, and area in drawer. You want these parts to in good shape cosy. If the parts don’t set strain on the dividers, lower new parts a very little for a longer time.
Phase four: Refill your drawer!
Then invite your buddies in excess of to present off your newly designed utensil drawer organizers. (That sounded much better in my head.)
The concealed advantages to this project had been that I cleaned my drawers, and taken out A Lot of products I didn’t genuinely use! I hope you relished this project, and that it influenced you to do a very little organizing of your have!
Extra Do it yourself drawer organizing tasks:
- Change a larger sized drawer to a utensil organizer.
- rapid suggestions and methods for attractive arranged desk drawers
- quick Do it yourself drawer organizer jewellery trays
Please be certain to pin this customized utensil drawer organizer publish for future reference:


